Compare

Quick Change Wet Mop Handles have a hinged side gate that allows mop to easily slide on and off handle. Rubbermaid Invader wet mop handles make removing and replacing mop heads easy and efficient. Features a durable polypropylene molded head for corrosion resistance, while a thumb wheel and side gate facilitate fast and easy changes. Wide head accommodates any size mop.

• Thumb wheel clamps mop head in place
• Plastic head w/ 60" wood handle
• Exclusive quick-change one-piece yoke holds mops 8-36 ounces mops
• 1" x 60" handle length

Our Dust Containment Kit for the Square Strip adds another dimension in controlling indoor airborne particles during dry stripping. Kit includes:

Lowest cost per square foot of all our marble and stone diamonds. - Available in 50, 120, 220, 400, 800, 1800, 3500 grit, these discs will completely restore your floor when used in succession. They smooth out a rough texture terrazzo and marble floors. These discs are used only on floors that are "pitted" or present a very "rough" texture. A velcro style back attaches directly to the face of the velcro disc holder or the male-to-male velcro kit.

• Available in grits from: 50-3500 grit.
• Large overall footprint allows for 3 diamonds to do the work of 5 x 3" while maintaining good machine balance.
• Tab provides easy removal from drive plate and allows "hang to dry" to help prevent mildew and increase life.
• A velcro style back attaches directly to the face of the diamond disc holder or the male-to-male velcro kit.
• Recommended for use on Terrazzo, Marble, Travertine and Limestone floors.
• The Scratch Removal Discs are designed to be used with water, do not run on a dry floor.
• Not for use on concrete floors.

Packaging

Packaging and Color Chart:

SRD'S are packed (3) per set

Average yield per set of of SRD's range from 3,000 - 5,000 square feet per set of 3 discs (depending on type of stone, floor condition and lippage).

Size: 2" x 6"

Available Grits:

Green, 50 grit

Black, 120 grit

Red, 220 grit

Yellow, 400 grit

White, 800 grit

Blue, 1800 grit

Gray, 3500 grit

Videos:

Specifications:

The SRD's are Designed for Performance

• Large overall footprint allows for 3 diamonds to do the work of 5 x 3” pads, while maintaining optimum machine balance.
• Floor contact is increased by 50%.
• The total labor savings is in excess of 40%.
• 66% of surface area moves in top 5% of pad driver speed versus less than 20% of conventional diamonds.
• Oversized design provides exceptional life.
• Segment height is 10 mm and weight is a full 2.2 oz.- almost double most other diamonds.
• Largest area's dimensions are 5.75" x 2.5"

The Velcro Tab - So Simple, So Effective

• Tab provides easy removal from drive plate and allows "hang to dry" to help prevent mildew and increase life of the hook and loop backing.
• Standard hook and loop back for ease of attachment and removal from driver.
• Male hook and loop adapter available to allow attachment to white floor pad for added flexibility.

More Info:

Directions:

Resurfacing and general scratch removal procedure:

Step 1: Resurface with Scratch Removal Discs

a) Thoroughly strip the floor to remove surface coating.

b) Hone the surface with Scratch Removal Discs and water.

Honing process time:

• Terrazzo and marble: 30 sec. per sq. ft.
• Granite: 1 min. per sq. ft.

c) Vacuum the slurry and rinse with "Neutral Stone Cleaner"

* Complete this step, then proceed to polishing with Wet Polish Powder

** The SRD's will not perform well if your floor has issues with lippage.

Engineered for exceptional performance and dust control, the TD-2500 Battery Powered Burnisher utilizes a 2.5 H.P. pad drive motor and the exclusive Dust Control System. This helps to reduce the need for dust mopping after burnishing by capturing finish compound and dust particles. The result is an innovative battery burnisher that provides high productivity, dust control, and increased labor saving benefits.

Clean-Air Filtration

Twin filters allow virtually dust-free burnishing, a significant factor when operating in sensitive environments such as schools, healthcare facilities, and retail stores. The filters are easily removable for washing and replacement as the need arises.

• Cover up to 20,000 square feet per hour with greater mobility and productivity.
• Compact design and low-profile base allow for easy access under shelving and fixtures.
• Effectively contain dust, protect indoor air quality, and eliminate the need for follow-up dust mopping
• Deliver outstanding gloss on a variety of finished floors with variable pad pressure for a clean, polished surface

TD-2500 Burnisher Features

• High capacity battery pack (3) 185 amp hour batteries
• Dust control system improves indoor air quality
• Variable speed drive system
• Excellent visibility from operators position
• Battery level indicator
• Easy access to filter cartridges

More Info:

• 20" Battery Powered Burnisher Brochure (pdf)

2500 rpm of Burnishing Speed

• Rugged roto-molded housing
• Adjustable pad pressure
• High-strength steel linkage mounted with a 2.5 HP motor.
• All this and more makes the TD-2500 the industry's premiere burnishing machine.

Simple to use and even easier to maintain, the T-2500 B far outperforms the competition's comparable units.

The sloped battery housing is designed with operator sight-lines in mind, allowing an unobstructed view of approaching obstacles. Safety switches prevent operation when the cover housing is removed or the pad holder raised.

Easy Pad Access

The TD-2500 tips back and rests on a specially-designed rear bumper. This permits easy pad holder access, pad replacement, and filter maintenance.

• Safety switches prevent operation when the cover housing is removed or the pad holder raised.

The in-line bristled brush is lightweight and effective, designed for cleaning grout lines on the fly while wet vacuuming. This not only eliminates the unnecessary cost and storage space of additional grout scrubbing brushes but also the time wasted changing tools while cleaning. Its heavy-duty bristles concentrate cleaning action deep into grout lines. For maximum flexibility, this practical tool also mounts easily on most vacuum wands on the market today and can be used in conjunction with virtually any vacuum head.

• Effectively cleans and scrubs grout lines.
• A Kaivac exclusive cleaning tool.
• Fits all Kaivac cleaning wands.
• Works on hard floor surfaces.

• KaiDri helps water sheet off hard surfaces to wipe out hard water spots before they get started.
• It also reduces the size of the water droplets, speeding up the drying process.

Directions:

• Blended yarn and looped ends minimize linting.
• Looped end covers twice the area per pass, compared to cut end mops.
• 4 ply, balanced blend of cotton and synthetic yarn for absorbency and strength.
• Outperforms and outlasts premium cut end mops two to one.
• 5" headband accommodates most mop handles.
• 1.25" headband on small size
• Economically priced
• Available Sizes: Medium, Large size

Packaging

Videos:

Specifications:

Wet Mop Sizes:

• Small, Equal to a 12 ounce, Headband size: 1.25 in.
• Medium, Equal to a 20 ounce, Headband size: 5 in.
• Large, Equal to a 24 ounce, Headband size: 5 in.
• The headband material is secured to the yarn with six rows of lock stitching, no less than six stitches per inch with all edges hemmed.
• Looped ends are laid side by side and secured to tailband with two rows of stitching, minimum of six stitches per inch.
• 5” headband sewn with six parallel rows of lock stitch thread.

More Info:

• Small looped mops are supplied with a YELLOW headband.
• Medium looped end mops are supplied with a GREEN headband
• Large looped end mops are supplied with a RED headband
• These are commonly accepted standards used for identifying wet mops.

Directions:

• No more lifted or "popped" tiles due to overuse of water and flooded floors.
• The ideal machine when you need to strip/scrub "half a hallway"
• A "Green Process" in floor care
• Chemical-Free
• No extra hand scrubbing required with the Square Strip. It does all the work!

Directions:

The BD-26 rider floor scrubber cleans large and small environments safely and productively, maintain and renew hard floor surfaces faster than ever before. The Tornado's 26" Ride-on Automatic Scrubber increases cleaning productivity in areas where walk-behind scrubbers were used in the past, thanks to its compact footprint and great maneuverability. Micro-rider leaves just-scrubbed floors left immediately clean, dry, and safe for traffic.

Tough, Long-Lasting Floor Scrubber

Healthier Buildings

• Compact Low-Profile - This highly maneuverable unit reaches difficult areas previously cleaned by larger ride-on scrubbers.
• Easy Access to Tanks and Batteries For easy maintenance, gain access to batteries by simply lifting the seat.
• Parabolic Squeegee - Heavy duty assembly featuring a four-sided rear blade with quick release lever to facilitate squeegee changes in 10 seconds or less.
• Silent Supervisor - Easy-to-read control panel displays battery run time and charge indicator, maximizing your team's cleaning efficiency and protecting your investment.

Disc Pads and Brushes - The BD unit comes standard with pad holders. When used with the appropriate pad, this is the ideal solution for daily maintenance cleaning. The BD-26 machine can be fitted with a variety of optional scrub brushes.

• Attaches directly to the Kaivac spreader frame
• Gently agitates the floors surface
• Safe on all floor surfaces

Microfiber floor finish bucket is the perfect, portable bucket is used to apply conventional water based floor finishes. The five gallon capacity bucket holds enough floor finish to coat 6,000 square feet before it's time refill. With the built-in washboard strainer on top, it's designed to remove excess debris and finish from flat mop - without transferring dirt back onto the floor.

Need to take a break between coats - no problem, simply snap the lid on the bucket and preserve your finish for hours.

• Easy to clean interior
• Wheels make it very easy to move
• Small size keeps it lightweight
• Drain valve allows finish to be emptied without having to lift the bucket
• Color-coded blue to visually differentiate use.
• Perfect for tamping excess finish from Microfiber flat mops.
• Smooth, non-porous surface makes it easy to clean

**Not for use with oil base / solvent based finishes.

Genuine Lambswool Applicator Pads are the professional floor specialists choice for a smooth even finish. From storefronts to gymnasiums, large areas and small, select from a full range of sizes.

This 100% natural lambswool pad offers efficiency and practicality. It can be washed and reused again and again and fits a standard threaded handle.

• 100% chrome tanned back
• Threaded handle not included (please order separately)

Ideal for the application of most oil based finishes and sealers.

Packaging

Videos:

Specifications:

Applicator Sizes:

10"- Part #: 0281010

12"- Part #: 0281212

16"- Part #: 0281616

Applicator Refill Sizes:

10"- Part #: 0280010

12"- Part #: 0280012

16"- Part #: 0280016

More Info:

Directions:

How to prep a Lambswool Pad prior to use:

1. Immerse the lambswool pad in a paint pan filled with mineral spirits for 5 to 10 minutes. This allows the lambswool pad to be more absorbent and help it spread urethane evenly.
2. Remove the lambswool pad from the mineral spirits and wring it out, allow the pad to remain damp but not soaked.
3. Install the lambswool pad on the applicator head by loosening the two wing nuts that hold the two pieces of the head together.
4. Wrap the lambswool pad around the bottom part of the head so that the wool is facing out. Make sure there is an even amount of the pad overlapping the top of the head on both sides.
5. Place the upper wood block onto the bottom block, sandwiching the lambswool pad between the two parts. Tighten the wing nuts to secure the pad in place.

How to apply finish with a Lambswool Applicator:

1. Open the container of oil base finish and pour it into a paint tray.
2. Dip the bottom of the lambswool pad into the finish. Drag the pad lightly across the edge of the paint tray to remove excess finish from the pad.
3. Place the lambswool pad on the surface of the wood and begin applying the urethane in long, even strokes going with the grain of the wood. When the finish becomes uneven, dip the pad back into the tray and re-wet.
4. Continue applying the finish until the entire surface of the wood is covered.

• Increases the slip resistance on finished floors
• Economical to use - highly concentrated
• The Best floor restorer on the entire planet!
• A long time favorite in our company since 1999

• Simply mix 1-2 ounces in a 32 ounce spray bottle and burnish away your problems.

Interim Maintenance:

Supplies You Will Need:

• A clean mop bucket and wringer
• A clean, wet mop
• An ultra high-speed floor machine (1500 rpm or more)
• Floor pads: Select from Natural Fiber, PT-3000 or Eraser floor pad

Packaging

More Info:

• Top Guard Frequently Asked Questions

Directions:

• Clean bucket and wringer.
• Wet mop - Rayon or Floor finish mops both work well (these mops will leave more product on the floor)
• High-speed floor machine (burnisher) 1500 -2000 rpm
• Floor pads: Select from any of the light-medium aggressive Natural Blend Hair pads.

• Fill Mop bucket with 1 gallon of cold water. (If unsure of amount, use an empty gallon container to help measure.)
• Squeeze Top Guard bottle to fill the chamber with two (2) ounces of Top Guard and pour into bucket.

• Squeeze Top Guard bottle to fill the chamber with one (1) ounce of Top Guard and pour into spray bottle. Fill spray bottle to top with cold water.

• Damp Mopping: Wring out the mop well. Top Guard should be applied to the floor a bit thinner than a coat of floor finish.
• Spray Bottle: Slowly swing your arm from side to side spraying Top Guard from the bottle in a stream (not a spray). Do not worry about applying Top Guard evenly, the floor pad will spread the solution evenly over the floor when burnishing.

Burnishing Instructions

Top Guard can be burnished Wet or Dry! When Damp Mopped, allow approximately 1 minute for Top Guard to begin to dry and burnish while still damp for best results. When applied via spray bottle, begin burnishing immediately after Top Guard has been applied to the floor. *Take your time when burnishing for the first few times for a stronger, deeper shine.

Things to Look for While Using Top Guard

Top Guard enhances the slip coefficient of the floor. Walk on the floor while it is wet and take note of how non-slip the floor appears. When dry, test the slip resistance of the floor ...... Incredible. Make special note of the gloss. It's deep and water clear, not hazy like polymer based restorers. Top Guard is the only Finish Enhancement product that eliminates the dust created from burnishing (even with propane). Remember to look at the bottom of the floor pad. There's no white ring, no build-up. The finish that's on the floor stays on the floor.

The Alpha VSP (variable speed polisher) Wet Polisher has new features to perform above and beyond your expectations. The VSP-320 includes a variable speed control switch with an automatic speed feed-back system to maintain consistent RPMs with or without a load.

The switch has also expanded the usable RPM range from 700 RPM to 2,800 RPM. The RPM range reduces heat build-up when polishing Engineered Stone, which eliminates burning or scorching the work piece. We added a Splash Guard that can be trimmed to adjust the height for the best comfort and protection. Every stone fabricator should try the VSP-320 variable speed wet polisher to achieve the best performance and high quality results.

Note: Please order the proper size backer pad, available in 3", 4" & 5" diameter. The backer pad is required, it's used to connect the diamond polishing discs to the polisher.

Included with each Hand Held polisher / grinder:

• Ground fault circuit interrupter (GFCI)
• Water valve & 15' feed hose
• Faucet / Garden hose adapter
• Wrench
• Side handle (reversible)
• Extra carbon brush set
• Splash guard
• Carrying case

The variable speed is the best all around polisher for use on floors, stairs, treads and risers.

Packaging

Videos:

Specifications:

Variable Speed, Hand Held Polisher Specifications

Voltage: 110/120 volts

Amps: 7.0

Power: 800 watts

Power cord: 10 feet

Speed (rpm): 700 - 2800 rpm

Hose length: 15 feet

Weight: 7.3 lbs.

Spindle: 5/8" x 11

More Info:

The major upgrade of the new 320 came in the form of the heavy-duty gear systems that includes the step-down transmission and a bevel and pinion gear to produce the variable speed range of 700 to 2,800 rpm.

• 15 ft. water supply hose
• Adjustable splash guard
• 15 ft. power cord

Directions:

• Provides instant access to heavy duty bristled floor brush when wet vacuuming floors
• Ideal for cleaning trouble spots on restroom and kitchen floors
• Swivel head easily reaches under low obstacles
• Squeegee Width: 14 in.
• Brush Width: 14 in.

The Easy Gloss System is a floor finish applicator designed to make floor finish coating faster and easier, while eliminating waste. The system features a lightweight applicator, convenient backpack and a microfiber applicator pad.

• Lightweight durable handle with finger tip dispense control.
• Padded backpack with adjustable straps for personal fit.
• Easy mounting applicator pad system.
• 1.5 gallon floor finish pouch included

Easy Gloss refillable 1.5 gallon bags are sturdy, reusable, and easy to fill and install. Bags can be filled with virtually any floor care chemical. Max liquid volume is 1.5 gallons. Under normal use conditions the pouch can be filled and reused up to 30 times.

*Not for use with oil base floor/wood finishes.

Easy Gloss Applicator Features

• Heavy Duty Canvas Backpack
• Ergonomically designed with padded, shoulder straps that are adjustable for desired fit

Refillable Floor Finish Bags

• Easy to fill and install
• Bags can be filled with virtually any non-acid floor care chemical
• 1.5 gallon capacity

Anodized Aluminum Handle - 56.5 inch

• Corrosion and shock resistant
• Lightweight

Swivel Trigger Operated Fluid Dispenser

• Allows quick and easy fluid dispensing
• Continuous flow when the valve is depressed
• Dual outlet dispenses fluid at a 90 degree angle - eliminates liquid collecting on the mop frame
• Swivel trigger moves with natural movement of operator making it more ergonomic.

Unique Frame Design

The 16" Cling-On molded flat mop frame with quick connector has molded-in spikes - the mop pad clings to the frame (no hook and loop strips) - and holds your mop pad firmly in place. Addresses ongoing nuisance issue of having to replace velcro strips that accumulate fiber and causes the frame to lose its grip on the mop.

Packaging

Easy Gloss Floor Finish Applicator Kit Includes:

• 56.5" Applicator handle
• 16" Nylon applicator pad holder - New
• Padded backpack with adjustable straps
• 18" applicator pad
• 7' supply tubing with pouch connector
• One refillable pouch (1.5 gallon capacity)

Videos:

Specifications:

More Info:

The 5' clean out fitting is a great option when a pressurized cleaning is necessary. Fits most standard faucets in commercial janitor sinks

• *Clean out fitting is an optional accessory
• Part #: 0354561

Specially designed filling station allows use of most water base floor finishes and many other cleaning chemicals such as neutral, general purpose, and disinfectant cleaners.

Refill stand kit is an optional accessory

The Refill Station Stand can be affixed to most flat surfaces (optional)

Using the funnel fill makes it easy to use in almost every cleaning environment.

• Simple funnel fill system
• Part #: 0354555

Directions:

Easy Gloss Floor Finish Applicator System

1. Prepare floor surface for coating.
2. Using the trigger at the top of the handle, depress to dispense a 4" puddle of floor finish onto the floor surface.
3. Applicator system will utilize the same application approach as conventional floor finish mop. Move applicator pad into the "puddle" to load the pad for initial use.
4. While moving applicator to new floor areas, dispense finish periodically and use U-shaped motion (section applications) as with conventional floor coating procedures.
5. Move at an even, uniform pace. Keep floor finish applicator pad uniformly wet with floor finish for proper coverage from one section to another.