Compare

The Earplug Dispensing Station is the ideal addition to any workplace environment where earplugs are necessary. This clutter free and convenient dispenser with comes with assorted colored earplugs and is perfect for both professional and personal use. Assembly on any wall is made simple with the attached mounting bracket and its hardware.

• Each dispenser is sealed and disposable
• Eliminates the mess of individually bagged packaging
• High visibility to increase awareness
• 100% PVC Free

Increased Compliance and Cost Savings

Convenient, quick access and ease of use lead to higher compliance. Plus, because workers take one pair at a time there is no wasteful grabbing of multiple pairs or pocket fill ups that end up getting trashed without being used. Less waste means more cost savings.

These disposable earplugs are ideal for:

• Construction zones
• Loud indoor settings
• Personal use

Features:

• Noise reduction rate (NRR) of 33dB
• Universal fit
• Disposable
• Easy assembly
• Comforting fit

Packaging

Available in two popular dispensing options

• MLX6644 contains 250 pairs of earplugs in the wall mount dispenser
• MLX6645 contains 500 pairs of earplugs in the wall mount dispenser

Videos:

Specifications:

More Info:

Directions:

1. ROLL and COMPRESS

With clean hands, hold earplug between thumb and forefinger as shown. Roll and progressively compress the entire tapered end of the earplug to a small wrinkle-free cylinder.

2. INSERT PLUG

To ensure fitting, reach hand over head and gently pull ear upward and outward as shown. Insert compressed, tapered end of earplug well inside ear canal. Hold 30-60 seconds until earplug expands. Release, then push in again for 5 seconds to ensure fit.

3. CORRECT FIT

When properly inserted, the bottom edge of earplug is located at the opening of the ear canal.

Lowest cost per square foot of all our marble and stone diamonds. - Available in 50, 120, 220, 400, 800, 1800, 3500 grit, these discs will completely restore your floor when used in succession. They smooth out a rough texture terrazzo and marble floors. These discs are used only on floors that are "pitted" or present a very "rough" texture. A velcro style back attaches directly to the face of the velcro disc holder or the male-to-male velcro kit.

• Available in grits from: 50-3500 grit.
• Large overall footprint allows for 3 diamonds to do the work of 5 x 3" while maintaining good machine balance.
• Tab provides easy removal from drive plate and allows "hang to dry" to help prevent mildew and increase life.
• A velcro style back attaches directly to the face of the diamond disc holder or the male-to-male velcro kit.
• Recommended for use on Terrazzo, Marble, Travertine and Limestone floors.
• The Scratch Removal Discs are designed to be used with water, do not run on a dry floor.
• Not for use on concrete floors.

Packaging

Packaging and Color Chart:

SRD'S are packed (3) per set

Average yield per set of of SRD's range from 3,000 - 5,000 square feet per set of 3 discs (depending on type of stone, floor condition and lippage).

Size: 2" x 6"

Available Grits:

Green, 50 grit

Black, 120 grit

Red, 220 grit

Yellow, 400 grit

White, 800 grit

Blue, 1800 grit

Gray, 3500 grit

Videos:

Specifications:

The SRD's are Designed for Performance

• Large overall footprint allows for 3 diamonds to do the work of 5 x 3” pads, while maintaining optimum machine balance.
• Floor contact is increased by 50%.
• The total labor savings is in excess of 40%.
• 66% of surface area moves in top 5% of pad driver speed versus less than 20% of conventional diamonds.
• Oversized design provides exceptional life.
• Segment height is 10 mm and weight is a full 2.2 oz.- almost double most other diamonds.
• Largest area's dimensions are 5.75" x 2.5"

The Velcro Tab - So Simple, So Effective

• Tab provides easy removal from drive plate and allows "hang to dry" to help prevent mildew and increase life of the hook and loop backing.
• Standard hook and loop back for ease of attachment and removal from driver.
• Male hook and loop adapter available to allow attachment to white floor pad for added flexibility.

More Info:

Directions:

Resurfacing and general scratch removal procedure:

Step 1: Resurface with Scratch Removal Discs

a) Thoroughly strip the floor to remove surface coating.

b) Hone the surface with Scratch Removal Discs and water.

Honing process time:

• Terrazzo and marble: 30 sec. per sq. ft.
• Granite: 1 min. per sq. ft.

c) Vacuum the slurry and rinse with "Neutral Stone Cleaner"

* Complete this step, then proceed to polishing with Wet Polish Powder

** The SRD's will not perform well if your floor has issues with lippage.